Correspondence table of enameled wire diameter and resistance value

Pay-off (link pull) ¡ú annealing ¡ú painting ¡ú baking ¡ú cooling ¡ú lubrication ¡ú take-up

Water quality affects the production of lacquer wires?

The production water production water in the lacquered wire has a variety of uses, and like, the requirements for water quality are also different. Depending on the purpose of use, the water quality can be divided into: annealing furnace water seal water, equipment cooling water, lubricant manufacturing water, etc.

The selection criterion of the electromagnetic wire is not considered for resistance, as the problem of resistance and fever can be done by selecting the same cross-sectional wire, it is the main consideration of the thick wire or the thin wire is mainly considered Operability.

To weld the lead aluminum enameled wire, it is necessary to remove the paint (there are very few household electric fans with very low requirements, and the ballast manufacturer does not remove the paint). The paint removal methods are listed below.
(1) It can be scraped with a blade,
(2) It can be peeled with a centrifugal knife,
(3) The paint can also be rubbed off with a grinding wheel,
(4) Of course paint remover is also available,
(5) You can also use high-temperature tin to burn the paint,
(6) Some people burn with fire
(7) Of course you can also use paint remover to remove paint

Enameled Rectangular Wire is one type of magnet wire, normally used for transformer, motors, generators, and gradually instead of round magnet wire.
Enameled Rectangular Copper Wire: A> 0.8–8mm, B> 1-22mm
Enameled Rectangular Aluminum Wire: A> 0.8–8mm, B> 2-22mm

AWG magnet wire is also called enamelled manganin wire which is composed of copper or aluminum conductor with insulation materials, such as PE, EI, UE, etc. The enameled wire have different performance according to chemical performance, heat resistance and others.

The Flat magnet wire size:
155 modified polyester enameled rectangle wire: a: 1.00-5.00;b: 2.00-16.00
180 polyester imied enameled rectangle wire: a: 1.00-5.00;b: 2.00-16.00
220 polyester imied enameled rectangle wire: a: 1.00-5.00;b: 2.00-16.00
200 polyester imeid/polyamide-imide enameled rectangle wire: a: 1.00-5.00;b: 2.00-16.00

The round enameled wire size
155 modified polyester enameled aluminum round wire: 0.25mm – 2mm
200 polyester imeid/polyamide-imide enameled round copper wire:0.016-7mm

Wire enamel insulating varnish is a kind of paint that can produce a good insulation layer between the wires in the winding. It is mainly used for the outer layer of bare copper wire, alloy wire and glass wire covered wire of various wire diameters to improve and stabilize the performance of enameled wire.

1. What factors affect the softness of the enameled wire and the elongation?

The softness and elongation are good to reflect the quality of the copper quality and the enameled annealing process, and they have a big relationship for the quality of the winding.

2. What is the effect of the thickness of the paint film?

The first tasty or coated is too thick to affect aging performance. The furnace temperature control has a greater impact on aging performance.If the evaporation zone is too sharp, it has a sparp and porront on the paint film, which is poor in these places. The heat of it is high, affecting the thermal aging performance.

3. EffectWhat are the reasons for the bucket breakdown voltage?

Oxe film circle. Overseas impurities in the paint film. Curing. The thickness of the paint film

4. What are the factors affecting the thermal shock??

Influence of the kitcase process. The effect of copper wire. Influence of paint

Resistance:
Take 1m of the enameled wire to be inspected, scrape off the paint film at both ends, measure the resistance of the enameled wire, the resistance measurement value should be within the resistance range of GB/T6109; the standard temperature is 20 degrees, the conversion formula: 20 degrees resistance/234.5+standard Temperature = actual measured resistance/234.5 + measured temperature;

7 type of enameled wire in accordance with insulation materials, list the thermal class, advatanges and application per type of enameled wire. Enameled wire types also can be divided into copper magnet wire and aluminum wire in accordance with conductor.

Axalta today announced that it has reached a final agreement to acquire Anhui Shengran Insulation Materials Co., Ltd. (“Anhui Shengran”). Anhui Shengran is a leading manufacturer of high-quality enameled wire paint in China. Its products are widely used in consumer electronics, electric vehicles and industrial fields. Subject to the conditions of the agreement, the transaction is expected to be completed in the second quarter of 2021. Financial terms have not been disclosed.

After the temperature resistance level is exceeded, the insulation layer will age, melt and crack. The result is that the insulation capacity is greatly reduced, and it is prone to increased loss, short-circuit failure, etc.

Paper insulation enameled transposition conductor characteristics:
1. There is no circulating current, the eddy current loss in the coil is small, and the current density can be improved;
2. Simplify the winding process;
3. The full rate is higher than that of the paper-covered wire slot.

Paper-insulated enameled transposed wires are mainly used in the coils of large transformers.

The voltage resistance performance of enameled wire is mainly affected by several factors:
1. The thickness of the insulating layer, not much nonsense;
2. The degree of aging of the insulating layer and the degree of baking affect the withstand voltage.
3. The quality of the insulation layer is mainly the pinhole performance.

Direct-welding enameled wire is named after its insulating layer uses an insulating material that can be directly destroyed at 360~420¡ã, and it can be directly welded without removing the insulating layer in advance during welding. Direct welding enameled wire is currently widely used in various industries of electromagnetic coils (motors, electroacoustics, inductance, etc.). As for whether it can be used to wind the motor coil, it mainly depends on the motor power or the working environment of the coil, and there is no problem within a certain temperature range.

Enameled Aluminum Wire connects Enameled Copper Wire with the short service life according to the test. The contact part of the enameled copper wire and the enameled aluminum wire will accelerate the oxidation of the aluminum wire.

Correspondence table of enameled wire diameter and resistance value
The resistivity of the copper wire ρ= 0.0172, the aluminum wire ρ = 0.0283, the wire resistance calculation formula:
R=ρ×L/S
(L = wire length, unit: meter, S = wire cross section, unit: mm^2)

The current mainly passes along the copper-clad aluminum wire on the surface of the wire, which is called the skin effect. The higher the frequency, the more obvious it is. The copper-clad aluminum wire uses this feature to save material. But its resistivity is slightly higher than that of pure copper wire, and the resistivity is also different with the thickness of the copper clad.

Enamelled wire stripper is specialized to depainting for transformer and electrical machine etc, and the different strippers can be chose and according to different heat resistance levels and different enamelled materials. The products include BT-112 strong enamelled wire stripper BT-105 quick enamelled wire stripper BT-101A/B stripper etc. Its characteristics BT-112 is applicable to depainting for the thrum of Copper Wire Aluminum Wire with the heat resistance level 180(H), 200(H+), 220(C). BT-105 is applicable to fast depainting for the thrum of enamelled Copper Wire Aluminum Wire with the heat resistance level 130(B), 155(F); BT-101A/B is applicable to depainting for voice coil wire EI.

Paper Wrapped Aluminum wire Production Process

One step :
Take the pure aluminum material drawing into the aluminium rod wire;

Two step :
Through the extrusion production line, take the aluminum rod wire into extruding and coarse drawing operation, then becoming the requirement specification of Bare aluminium wire;

Three step :
Take up the Bare aluminum wire conductor, and inspection the bare wire coil products;

Four step :
Annealing the bare aluminum wire, and placed neatly, ready to production;

Five step :
Doing the digital dividing and cutting paper process and finished;
Pay-off the wire coil products, ready to paper covering production;

Six step :
Taking into straightening and tension lenvelling operation, ready to paper winding;

Seven step :
Taking into the paper winding operation, and then for inspecion;

Eight step :
Pulling the finished paper-covered wire, and then for take-up the wire coil , ready to packing.

Carbon aluminum wire is an aluminum wire for parts manufacturing of various machines.08 and 08F aluminum wire for rolling thin plates, deep-drawing products, oil drums, high-grade enamel products, less demanding carburizing and cyanide parts, welding rods, etc.

Enameled wire is a main type of winding wire. It is composed of a conductor and an insulating layer. After the bare wire is softened by annealing, it is painted and baked many times.

General purpose enameled wire (ordinary wire): Mainly used for winding wires in general motors, electrical appliances, instruments, transformers, etc., such as polyester enameled wire and modified polyester enameled wire.

Advantages of oxide film wire
1. The oxide film is not sealed by insulating paint, and the temperature resistance can reach 250¡æ. The heat resistance of the oxide film sealed with insulating paint depends on the temperature index of the insulating paint;
2. High slot full rate, light weight and good radiation resistance.

The AWG tables are for a single, solid and round conductor. The AWG of a stranded wire is determined by the cross-sectional area of the equivalent solid conductor. Because there are also small gaps between the strands, a stranded wire will always have a slightly larger overall diameter than a solid wire with the same AWG.

Enameled wire is a type of electromagnetic wire, usually refers to the insulation wire used to make coil or winding in electrical products. It is also called the winding wire.
The electromagnetic wire must meet the requirements of various applications and manufacturing processes. The former includes its shape, specification, working at high temperature in short and long time, as well as the strong vibration and centrifugal force under high speed on certain occasions, resistance to corona and breakdown under high voltage, and chemical corrosion resistance in special atmospheres, and the requirements for tensile, bending and wear, as well as the requirements of drawing, bending and wear during winding and inlaying. Swelling and erosion during immersion and drying.

British Standard Wire Gauge (often abbreviated to Standard Wire Gauge or SWG) is a unit for denoting wire size given by BS 3737:1964 (now withdrawn). It is also known as the Imperial Wire Gauge or British Standard Gauge. Use of SWG sizes has fallen greatly in popularity, but they are still used as a measure of thickness in guitar strings and some electrical wire. Cross sectional area in square millimetres is now the more usual size measurement for wires used in electrical installation cables. The current British Standard for metallic materials such as wire and sheet is BS 6722:1986, which is a solely metric standard.

1. Polyester enameled wire (P.E.W.)
Polyester enamel-covered wire is made of heat-resistant Terephthalic Polyester resin as the main grease as the insulating film and baked on the conductor. Its characteristics are as follows:
¡ñThe heat resistance is superior to synthetic tree (P.V.F.) enameled wire and U.E.W. enameled wire.
¡ñExcellent chemical resistance (except alkaline) and solvent resistance.
¡ñThe mechanical strength is comparable to synthetic resin (P.V.F.).
¡ñThe force rate and dielectric rate are comparable to U.E.W. enameled wire.
¡ñAlkali resistance and moisture resistance are better than synthetic resin enameled wire (P.V.F).

In theory, any enameled wire can realize the mutual conversion between electric energy, magnetic energy and kinetic energy. However, the use of enameled wire has a processing process, and electrical products also have different working environments. Therefore, in the selection of enameled wire And when substituting, the characteristics of various enameled wires must also be considered.

Best Price Factory Sale Enameled Copper Coated Aluminum Wire can be used at a working temperature of 180 ClassC. The product has the advantages of direct solderability, good coloring, and low dielectric loss under high frequency. Widely used in windings and wiring of motors, electrical appliances, electronic components, meters, etc.

Double Glass-fiber Covered Rectangular Aluminum Wire is a kind of winding wire made by electrician round aluminum rod drawn or extruded into a rectangular conductor by a certain specification die, and then a double glass fiber insulation layer is wrapped on the rectangular conductor.

¡ñ Conductor resistance. Measure with a conductor resistance tester, and then change to the value at 20¡ãC for comparison.
¡ñInsulation destruction voltage. Twist two enameled wires, apply voltage between the conductors, and judge by the damage voltage of the paint film. This performance is analyzed and judged through two tests of normal state and cold state breakdown voltage.
¡ñPaint film continuity (pinhole). Check the small holes of the paint film with a certain length of the test material. The project is tested by a high-pressure paint film continuity tester.