American wire gauge AWG

After the temperature resistance level is exceeded, the insulation layer will age, melt and crack. The result is that the insulation capacity is greatly reduced, and it is prone to increased loss, short-circuit failure, etc.

For Aromatic polyimide tape-covered aluminum magnet wire, after the aluminum magnet wire is taped with a tape that is 1.5 mm thick with 1.0 mm of this thickness being polyimide film and the remaining 0.5 mm being fluoroplastic, it is heated and heat-sealed.

Another important usage of copper is in manufacturing wire gauges that are largely use in measuring the diameter of wire.
Similarly aluminium is also largely use for electrical application.

3M paper covered aluminium wire feature :
* High dielectric strength/Excellent therm alstability/Wrapped tightly;
* Paper covered Aluminum wire is a special kind of magnet wires. Its conductors is electrical round aluminum rods which squeeze
and draw by the certain size of mold. And its insulations is special material;
* Our 3M paper covered aluminum wire uses two layers or several layers as the insulation layer;
* The wrapping direction of paper is same. And every layer paper twines conductors continually and compactly without wrinkles;
* Uses for oil-immersed transformers, reactors and other windings;

Speaking of the copper enameled wire, I believe everyone should know. Today, we introduce you to a wire, ie the copper paint package. Let us simply look at the transportation and preservation of copper-clad aluminum wires, because if many wires are transported incorrect, it is very likely to be used, so let us simply understand the transportation and preservation of the copper paint wire, so you can be here.

The infrared spectrum analysis test is based on the standard UL746A, which only confirms the chemical composition of the paint film, establishes the infrared spectrum and retains it. After the enameled wire is certified, samples will be sampled for testing every year during the follow-up inspection service. The infrared spectrum made by the paint film on the sampled sample needs to be compared with the infrared spectrum established on the sample at the time of certification. The two infrared spectrums must be comparable. superior.

With the continuous progress of society and the continuous development of industry, enameled wire has a very broad application field and has become an indispensable main supporting raw material for products such as motors, electrical appliances, household appliances, electronics, communications and transportation, especially in recent years. The rapid development of household appliances, the advancement of electronic technology, and the rise of the communication industry have provided new space for the application of enameled wires, adjusted the application proportions in various fields, and will also put forward higher and newer technical requirements for enameled wires, and adjust enameled wires. The proportion of the structure. After joining the WTO, the enameled wire industry will face competition in the domestic and international markets, which adds a layer of thinking and pressure to corporate leaders.

Copper Clad Aluminum Wire is a new enameled wire, is composed of aluminum conductor covered with copper materials, maybe self-bonding, also called self-bonding enameled wire. And the short word is ECCA.

Kraft Insulated Copper Stranded Paper Covered Wire refers to the insulation layer of the wire wrapped with cable paper. The paper covered wire insulation has at least 3 layers to wrap the paper tape. When it exceeds 3 feet, the innermost and outermost layers should be covered and wrapped, and the rest can be wrapped around with a gap of no more than 2mm. When the width of the paper tape is 9.5 When mm and above, the gap should not exceed 3mm.

Wire for winding used in electrical equipment is generally called magnet wire. Simply put, ¡°Magnet wire is used for interchanging electrical energy with magnetic energy¡±.
Magnet wires are broadly divided into enamelled wire (coating insulation), covered conductor wire (fiber/film insulation), other specially formulated wire, and combinations thereof.

The difference between enameled aluminum wire and enameled copper wire of vibration motor: the resistivity of copper wire is 0.017, and the resistivity of aluminum wire is 0.028. The cross-sectional ratio of copper wire and aluminum wire interchange is 0.79:1, and six square copper wires are equivalent to ten square aluminum wires. The diameter of the aluminum wire is thicker than that of the copper wire, and the same aluminum wire of the stator slot will not fit.

Thermal Class 105 / 133 / 155 Grade Enameled Wire includes
Polyethylene formaldehyde enameled copper wire (PVF)
Polyester enameled copper wire (PEW)
Polyurethane enameled copper wire (UEW).
Application: Normally used for Oil-filled transformers, motors, micro motors, transformers and high frequency coils, relays, magnetized coils

Copper-clad aluminum wire refers to a wire with aluminum core wire as the main body and a certain proportion of copper layer plated on the outside. It can be used as a conductor for coaxial cables and wire and cable conductors in electrical equipment. The aluminum wire has a small specific gravity, but its welding performance is not good. Therefore, the copper-clad aluminum wire is wrapped with a copper layer on the aluminum wire. This copper-clad aluminum wire can not only take advantage of the small aluminum specific gravity, but also improve the welding performance.

Round Enameled Wire type: Aluminum Wire and Copper Wire
Application:used for transformers, inductors, motors, generators, dry type transformer, Cast Resin Transformers
Dimension: Aluminum : 0.2-9.2mm; Copper: 0.016-7mm

¡ñ Conductor resistance. Measure with a conductor resistance tester, and then change to the value at 20¡ãC for comparison.
¡ñInsulation destruction voltage. Twist two enameled wires, apply voltage between the conductors, and judge by the damage voltage of the paint film. This performance is analyzed and judged through two tests of normal state and cold state breakdown voltage.
¡ñPaint film continuity (pinhole). Check the small holes of the paint film with a certain length of the test material. The project is tested by a high-pressure paint film continuity tester.

ISO Certificated Polyimide Round Enamel Coated Magnet Wire has better performance than all other types of enameled wires. Polyimide paint film has only abrasion resistance slightly worse than polyester and polyvinyl acetal enameled wires. In order to improve this performance, most of the current Use polyester imide and polyamide imide to prepare enameled wire, which can increase the solid content of the paint, but the heat resistance is somewhat reduced.

The samples for the dielectric strength test are also twisted pairs, and the number is 5 pairs. During the test, the voltage was applied at a boosting rate of 500V/S until breakdown, and the voltage at the time of breakdown was recorded. The requirements for dielectric strength in the NEMA MW1000 standard will vary according to different wire diameters, different paint film thicknesses, and different enameled wire types.

A brief introduction to the advantages and disadvantages of copper wire and aluminum wire:Same area:

1, copper wireis large load than aluminum wire . 2, copper wire is more flexible than aluminum wire. 3 copper wire is lower resistivity than aluminum wire. 4,copper wire is more stable than aluminum wire. 5, however, copper wirer price is 3.5 times higher than aluminum wire.

Aluminium Alloy Wires are made from a wide range of aluminum alloys, depending on the customer requirements. Aluminium wires are sold to manufacturers of eyelets, rivets, nails, screws and other various products. Bare Aluminium Wire is used for Cables, Junctions, Rivets, Hangers, Clips and other household Items.

The selection criterion of the electromagnetic wire is not considered for resistance, as the problem of resistance and fever can be done by selecting the same cross-sectional wire, it is the main consideration of the thick wire or the thin wire is mainly considered Operability.

Advantages of enameled CCA wire:
As envelope alternatives of pure enameled copper wire, it has good performance of high frequency transmission, originally it was applied in various types of high-frequency electromagnetic induction coil; now in order to save more production cost, ECCA wire has been widely used in various types of electronic coils, transformers, inductors, rectifiers, and all kinds of large and small motors, and has excellent soldering performance. Its density is low, the weight of the unit product can at least save 40% of the copper wire, it can save a lot of cost of production material.

Generally speaking, UL certified enameled wire needs to do four tests:
Thermal Aging Test (Full Thermal Aging Test or One Temperature Thermal Aging Test)
Dielectric Strength Test
Elongation and Heat Shock Test
Infrared Analysis – IR

The wrapped wire is made of natural silk, polyester fiber, glass fiber, insulating paper or synthetic resin film, etc., tightly wrapped on the conductive wire core to form an insulating layer. There are also insulating layers wrapped around the enameled wire. In addition to thin-film insulation, others such as glass filaments need to be dipped in adhesive insulating varnish to improve their electrical, mechanical and moisture-proof properties. In fact, they are combined insulation.

Question: During our production process, we found that one axis of enameled wire is wound around the axial inductance. This axis of enameled wire and other axis of enameled wire are wound on the same magnetic core. The inductance of the enameled wire with this axis is relatively high. We made 1mH inductance, and the enameled wire of the other axis was only 960uH, and the problematic wire of this axis was 1.025mH, and the inductance test frequency was 796kHz. (1) The number of stitches is the same as the number of turns, excluding the slip ring. (2) The 1-meter straight resistance is a bit smaller than that of other shafts. I personally think that the enameled wire contains magnetic substances, but if it contains magnetic substances, the resistivity should be greater, and the DC resistance should be greater. So please help to solve the problem, or have encountered this kind of problem before, please analyze it, thank you in advance!

Telephone cable is usually thought of only as a communication medium operating at a normal 48 Vdc level. But telephone cable is regularly used by telephone operating companies to supply power to remote telephony equipment such as: PCM (Pulse Code Modulation) repeaters, FDM (Frequency Division Modulation) repeaters, telegraph and various types of control circuits. The normal talk battery voltage is regularly exceeded in the case of long subscriber loops utilizing loop extenders and on dial long line circuits which operate in the 70 to 100 Vdc range. For these applications, the referenced devices are generally current limited to approximately 150 milliamps. In all such cases, normal telephone industry practice usually limits pair-toground applied voltage to 150 Vdc, and pair-to-pair voltage is usually limited to 300 Vdc.

The main advantage of the TIW wires is relatively high electric strength of the insulation, with breakdown voltage min. 6kV. Obtaining such a high resistance was possible by the use of a reinforced, three-layer conductor insulation. Third external insulation made of polyamide gives excellent flexibility and high mechanical resistance of the wire. Normally, TIW wires are produced in thermal class B. Fully automated manufacturing process provides a central position of conductor and the same thickness of insulation at any point of the wire.

Water quality affects the production of lacquer wires?

The production water production water in the lacquered wire has a variety of uses, and like, the requirements for water quality are also different. Depending on the purpose of use, the water quality can be divided into: annealing furnace water seal water, equipment cooling water, lubricant manufacturing water, etc.

Enameled wire is a main type of magnet winding wire. It is composed of a conductor and an insulating layer. After the bare wire is softened by annealing, it is painted and baked many times. However, it is not easy to produce products that not only meet the requirements of the standard, but also meet the requirements of customers. It is affected by the quality of raw materials, process parameters, production equipment, environment and other factors. Therefore, the quality characteristics of various enameled wires are different, but they all have Mechanical properties, chemical properties, electrical properties, and thermal properties

Special Insulated Rectangular Wires include fiberglass covered wire, paper covered wire, kapton insulated wire. Except Insulated Rectangular Wires, also provide the round special insulated wire.